Teac WR-DA7 Uživatelský manuál

The meter bridge shown in photo is one of the optional accessories.Application GuideVersion 2Audio MixerWR-DA7

10SYNC OUT terminal of the DA-88 to the WCK IN terminal of the WR-DA7. Then press the D-I/Oswitch of the WR-DA7 several times in order to display the

112.5 DAT (with AES/EBU or S/PDIF I/O)To record and playback using the DAT Recorder as the wordclock master and the WR-DA7 as aslave, connect the DAT

12Normally, a Macintosh computer has two serial ports: modem and printer port. RAMSA MAX soft-ware permits connection of either of these ports to the

13Set the OMS as follows:Start the OMS setup application. If the OMS is not installed, it can be downloaded from themanufactures web-site.Select [OMS

153. WR-DA7 system applications 3.1 Example of systems for ADAT (1 unit) (When a timecode is recorded on a tape track)This system is used to record th

16System configuration-1WCK MASTERWR-ADATADATDIGITALOUTTRACK8ANALOG OUT(RCA)ININOUTOptical CableWR-SMPTSMPTE INSLOT 1(17-24ch)(XLR)SPAES/EBUSPPowerAMP

173.2 Example of systems for ADAT (3 units) and BRC This system is configured using 3 ADATs and a BRC connected using the ADAT Sync cables and thethr

18During ADAT playback there will be no playback while ALL INPUT is ON. ALL INPUT must beturned OFF. BRC setting Select the Fixed Mode when the BRC is

19System configuration-2WCK MASTERWR-ADATADATADATID1BRCWR-DA7DIGITALOUTINMIDI INMTCMMCMIDI OUTWCK OUT(48kHz OUT)REMOTE OUT TO ADATSync CableWORD CLO

203.3 Example of systems with Two WR-DA7 in tandem with 4 ADATs and BRC This is a 32-track digital recording system utilizing two WR-DA7’s connected i

Limit of Liability/Disclaimer of Warranty: The author, Audio Video Systems Division ofMatsushita Communication Industrial Co., Ltd has used its best e

21For proper tandem connections, select the TANDEM setting to ‘ON’ in the TO SLOT screen of theD-I/O Input Setup Section. To operate MMC, set the MMC

22To accomplish MMC operation, the MIDI channel of the WR-DA7 and the MIDI channel of the BRCmust be set to the same channel. On the BRC, obtain a dis

23WCK MASTERWR-ADATADATID1ADATID2BRCWR-DA7DIGITALOUTINMIDI INMMCMTCMIDI OUTWCK OUT(48kHz OUT)REMOTE OUTTO ADATSyncCableWORD CLOCK IN (75Ω=OFF

243.4 Example of systems with 3 DA-88sThis is a 24-track digital recording system that uses three DA-88’s. The DA-88 can generate SMPTEtimecode and MT

25DA-88 setting Since the DA-88 receives digital input data from the TDIF-1, press the DIGITAL IN switch on thecontrol panel. The machine ID number of

26System configuration-4WCK MASTERWR-TDIFDA-88DA-88DA-88with SY-88ID0WR-DA7TDIF-1 TDIF-1WORD SYNC OUT(BNC)(BNC)MIDI INMTCMMCMIDI OUTWORD CLOCK IN

273.5 Example of systems for WR-DA7 tandem connections with DA-98 (1 unit)and DA-38 (3 units) This is a 32-track digital recording configuration using

28WR-DA7 setting To use the WR-DA7 as a slave unit, set the SOURCE SELECT to ‘WCK IN’ in the INPUT SET windowof the D-I/O Setup Section on the MASTER

29WR-DA7MIDI INMMCMTCMIDI OUTWR-TANDMSYNC OUTSLOT 1(17-24ch)(MASTER)(MASTER)(SLAVE)SLOT 2(25-32ch)SLOT 3INPUT 1-16WORD CLOCKOUT (75Ω=OFF)To PCWORD C

303.6 Example of systems for analog 16-track recorder (1 unit) This is an editing system that uses AUTOMATION. The SMPTE timecode is recorded in the 1

3Table of Contents1. Introduction... 42. Notes for connections w

31System configuration -6WCK MASTERWR-ADDA16Track AnalogMultitrack RecorderTrack16Analog OutOUT88WR-SMPTSMPTE INSLOT 1(17-24ch)(XLR)INPUT 1-16WR-ADDAO

323.7 Example of systems for Digital Video Recorder (1 unit) This is a post-production system consisting of the WR-DA7 and the Digital Video Recorder.

33System configuration -7WR-SMPTWR-DA7SW-OFFREFOUTSMPTE OUT(XLR)DIGITALIN/OUTDIGITAL I/O(XLR)(D-sub25pin)(BNC)REF INV-SYNC IN(BNC)SMPTE IN(XLR)

343.8 Example of systems for VTR (1 unit), ADAT (1 unit), and BRC This is a post-production system consisting of the ADAT and the BRC, in addition to

35BRC setting To synchronize the BRC with the SMPTE timecode from the video recorder set Locate Reference to‘SMPTE Input’ and Clock Source to ‘Interna

36System configuration -8WCK MASTERBRCWR-DA7SYNC INSMPTE INSMPTE TimecodeMIDI INMTC MIDI INREC OUTVIDEOOUTMMC MIDI OUTMIDI OUTWCK OUT(48kHz OUT)REMO

373.9 Example of systems for VTR (1 unit) and DA-98 (1 unit) This is a post-production system consisting of the DA-98, one WR-DA7 and a video recorder

38To enable the DA-98 to receive digital input from the TDIF-1, press the DIGITAL IN button on thefront panel. When the timecode output of the video r

39System configuration-9VIDEO INWORD SYNC OUT(BNC) SMPTETimecodeMIDI INMTC MIDI INMMC MIDI OUTMIDI OUTTIMECODE INDA-98 ID1House Video Syn

403.10 System Example of Pro ToolsThis example illustrates using the WR-DA7 in a Pro Tools system. Editing can be performed usingAutomation, etc. af

41. IntroductionThis Application Guide supplies examples for interfacing the WR-DA7 with commonly usedperipheral recording equipment. This guide’s dia

41To display MTC timecode on the LCD screen set the [Time Base] to [MTC] in the AutomationExecute screen of the WR-DA7.To use MMC set the [MMC Port] t

42System Configuration-10WCK MASTERWR-ADATADAT888 I/OPro ToolsID1ADATID2BRCWR-DA7DIGITALOUTINMIDI INMIDIOUTWCK OUTSYNC OUTSyncCableWORD CLOCK INPORT

433.11 System Example of MIDI Sequencer (Performer)This example illustrates the WR-DA7 mixing automation system using MIDI sequencer software(Perform

44To use Control Change, set [Tx, Rx] and NRPN to [ON] in the CTRL CHG setup area of the MIDISetup Window.To use System Exclusive set [Tx, Rx] to [ON]

45System Configuration-11WCK MASTERWR-ADATADATADATID1BRCWR-DA7DIGITALOUTINMIDIOUTINOUTMIDIINWCK OUTSYNC OUTSyncCableWORD CLOCK INININOUTOptical CableW

463.12 System Example of WR-DA7 Tandem-Connection to a MIDI Sequencer (Performer)This example refers to the configuration a mixing automation system

47WR-DA7 SetupTo set the WR-DA7 tandem master and slave as the WCK (wordclock) slave, set the [Source Select]to [WCK IN] in the D-I/O Input Set screen

48MIDI Sequencer (Performer) SetupTo record WR-DA7 operation in the MIDI sequencer (Performer), start [Patch THRU] on the Basicmenu and set [Select Pa

49System Configuration-12WCK MASTERWR-ADATADATID1ADATID2BRCWR-DA7DIGITALOUTININWCK OUT(48kHz OUT)REMOTE OUTTO ADATSyncCableWORD CLOCK IN (75Ω=O

503.13 System Example of AKAI DR8 (1 unit)This example refers to a system consisting of an Akai DR8 hard disk recorder and a WR-DA7 con-nected using

52. Notes for connections with peripheral equipment2.1 WordclockThe WR-DA7 as wordclock masterThe DA7 has an internal wordclock generator that provide

51System Configuration-13WCK MASTERWR-ADATDR8DIGITALOUTINwith IB-804A (IB-803M)INOUTOptical CableWR-SMPTSMPTEOUTMIDIOUTMIDIINMIDI OUTMIDI INMTCMMCSMP

523.14 Connection to MAX (Macintosh) expansion softwareThe example refers to the building of a recording and mixing automation system using one WR-DA

53System Configuration-14MIDI INMIDI INMIDI OUTMIDI OUTDA-98WR-TDIFWR-DA7INPUT 1-16RSRMicSamplerKeyboardSPMONITOR AAES/EBUSPPowerAMPRECOUT2TRA INDAT

543.15 Connection to MAX (Macintosh) expansion software and Other Sequence SoftwareThis example illustrates a recording and mixing automation system

55Macintosh SetupTo have the Macintosh recognize the MIDI Timepiece A/V and various MIDI devices using FreeMIDI.Open Free MIDI Preferences in the File

56System Configuration-15WR-DA7MIDI OUTMIDI INMIDIINMIDIOUTMIDI INMIDI OUTMIDI OUTMIDI ININPUT 1-16RSRSamplerKeyboardSPMONITOR ATo PCAES/EBUSPPowerAMP

573.16 Tandem-Connection to MAX (Macintosh) expansion softwareThe example refers to a recording or mixing automation system using two WR-DA7s and PC e

58MIDI Timepiece A/V SetupFor tandem communication between the two WR-DA7s, establish connections from Port 1 OUT toPort 2 IN and from Port 2 OUT to P

59System Configuration-16WR-DA7MIDI INMIDIOUTWR-TANDMSYNC OUTSLOT 1(17-24ch)(MASTER)SLOT 2(25-32ch)INPUT 1-16WORD CLOCKOUT (75Ω=ON)To PCWORD CLOCK IN

603.17 Tandem-Connection to MAX (Macintosh) expansion software and Other Sequencing SoftwareThis example refers to the building of a recording or mi

6WR-AESS: Select the switch (AES/EBU, S/PDIF) on the card, according to the devices beingconnected. It is possible to select settings for each pair of

61WR-DA7 SetupThis system uses the DA-98 as word clock master. Since the DA-98 is connected to Slot 1 of themaster, set [Source Select] to [Slot 1] o

62MIDI Sequencer (Digital Performer) SetupTo receive MTC from the DA-98 through the MIDI Timepiece A/V , set the Sync Port to [Modem] inthe Receive Sy

63System Configuration-17WR-DA7MIDI INMIDIOUTMIDI INMIDI OUTMIDI INMIDI OUTWR-TANDMSYNC OUTSLOT 1(17-24ch)(MASTER)SLOT 2(25-32ch)INPUT 1-16WORDCLOCK

aV0599-1069 DA7AppliGuide Printed in Japan Matsushita Communication Industrial Co., Ltd. 1999

7Tandem connectionMake all connections with the mixers turned OFF. You will need the following cables and cards: (2) WR-TNDM cards, (1) Tandem cable (

82.3 ADAT, BRC Connections To connect an ADAT with the WR-DA7 digitally, the WR-ADAT option card is needed to connect theoptical cables. Install the c

9When a MIDI message is received at the MIDI IN terminal of the BRC it is immediately transferredas a through output from the MIDI OUT terminal. To se