Teac HS-2000 Uživatelský manuál stáhnout pdf (Strana 13)

TASCAM HS-2000

2 − Names and functions of parts

Rear panel

hANALOG IN [LINE] connectors (L/R)

These are balanced analog XLR connectors for line

input.(1: GND, 2: HOT, 3: COLD)

jDIGITAL IN [LINE] connector

This balanced XLR connector is for digital audio input

in AES3-2003/IEC60958-4 (AES/EBU) or IEC60958-3 (S/

PDIF) format.

Sampling frequencies of 88.2 and 96 kHz are

transmitted at double speed. Sampling frequencies of

176.4 and 192 kHz are transmitted at quadruple speed.

The built-in sampling rate converter can handle 32–

192 kHz.

kANALOG OUT [MONITOR] connectors (L/R)

These balanced analog XLR connectors output the left

and right monitoring signals. (1: GND, 2: HOT, 3: COLD)

lRS-232C connector

Connect an external controller, for example, to this

9-pin

D-sub connector for RS-232C serial control.

NOTE

It cannot be used at the same time as the RS-422

connector. (See “RS-232C page” on page 107.)

;PARALLEL connector

Connect a TASCAM RC-SS20 or other external

controller to this 25-pin D-sub parallel control

connector.

zAC IN connector

Connect the included power cord here.

xANALOG OUT [LINE] connectors (L/R)

These balanced analog XLR connectors are for line

output. (1: GND, 2: HOT, 3: COLD)

cDIGITAL OUT [LINE] connector

This balanced XLR connector is for digital audio output

in AES3-2003/IEC 60958-4 (AES/EBU) format.

Sampling frequencies of 88.2 and 96 kHz are

transmitted at double speed. Sampling frequencies of

176.4 and 192 kHz are transmitted at quadruple speed.

vREMOTE connector

Connect a TASCAM RC-HS32PD or RC-HS20PD remote

control (sold separately) here.

CAUTION

Never connect this to a network using an Ethernet cable.

Doing so could damage this unit or network equipment.

bRS-422 connector

Connect an external controller, for example, to this

9-pin D-sub connector for RS-422 serial control.

NOTE

It cannot be used at the same time as the RS-232C

connector. (See “RS-422 page” on page 108.)

nTIMECODE INPUT connector

This balanced XLR connector is for SMPTE timecode

input.

mTIMECODE OUTPUT connector

This balanced XLR connector is for SMPTE timecode

output.

,WORD/VIDEO IN connector

This BNC-type connector accepts a word clock signal

(44.1kHz, 48kHz, 48kHz pull-down, 48kHz pull-up,

88.2kHz, 96kHz, 176.4kHz, 192kHz) or a video reference

signal (NTSC/PAL black burst signal, HDTV Tri-Level

signal).

Use the switch to turn the integral 75Ω terminator on

or off.

.WORD/VIDEO THRU/OUT connector [cut “WORD”]

This BNC-type connector outputs a word clock signal

(44.1kHz, 48kHz, 48kHz pull-down, 48kHz pull-up,

88.2kHz, 96kHz, 176.4kHz, 192kHz or thru) or a video

reference signal (IN connector signal thru only).

Use the THRU/WORD OUT switch to set the signal

output.

/75Ω ON/OFF/THRU/WORD OUT switch

Use this three-way switch to make one of the following

settings.

Terminator OFF and WORD/VIDEO THRU

Terminator OFF and WORD OUT (no VIDEO OUT)

Terminator ON and WORD OUT (no VIDEO OUT)

!ETHERNET connector

Use this Ethernet connector to connect the unit with

a network for file transfer and to control this unit from

another device on the network.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 155 156

Komentáře k této Příručce

Žádné komentáře

Teac HS-2000 Uživatelský manuál Strana 13

Komentáře k této Příručce

Související produkty a manuály pro Audio Teac HS-2000